How To Weigh A Horse? - Equine Assisted Psychotherapy

The calculation: (heartgirth x heartgirth) x body length ÷ by 330. This gives the weight of the horse in pounds (lbs). The heartgirth measurement: Take a measuring tape and measure all the way around the horse’s girth from the highest point of the wither going to just behind the elbows.

What is the most accurate way to weigh a horse?

The most accurate method for estimating a horse’s weight using a weight tape is the formula method, which requires two measurements be made in inches. When a weight scale is not available or practical, the formula method is the method of choice.

What are the 3 most common ways to weigh a horse?

There are three common ways to weigh a horse. The most accurate method is to use a livestock scale. The next best method is to estimate your horse’s weight using a weight tape or online calculator. The alternative is “eyeballing it,” which is least accurate.

Are horse weight tapes accurate?

Weight tapes aren’t very accurate at telling you how much your horse weighs. While two horses may have the same girth circumference — what you measure with the tape — differences in their body type cause them to weigh different amounts.

How do you weigh a horse with a weight tape?

The heartgirth measurement: Take a measuring tape and measure all the way around the horse’s girth from the highest point of the wither going to just behind the elbows. The body length: Measure from the point of shoulder in a straight line around to the point of buttock on one side. The result is in pounds (lbs).

How much does a Quarter horse Weigh?

The height of mature animals varies from 14.3 to 16 hands (about 57 to 64 inches, or 145 to 163 cm), and their weight varies from 950 to 1,200 pounds (431 to 544 kg). They have a calm, cooperative temperament.

How much do Clydesdale weigh?

weigh between 1,800 and 2,300 pounds.

Can you be too heavy to ride a horse?

Deb Bennett, PhD, founder of the Equine Studies Institute and an expert in the biomechanics of horses, has advised that the “ Total weight of rider plus tack must not exceed 250 lbs. There is no horse alive, of any breed, any build, anywhere, that can go more than a few minutes with more weight on its back than this.

How often should you check your horses weight?

It is advisable to monitor your horse’s body condition and weight regularly, at least every two weeks where possible. If there are any specific concerns regarding weight or condition, more regular monitoring is desirable. This is important to ensure a horse’s diet is well matched to its work load.

Is laminitis fatal in horses?

Laminitis is a deadly disease. Find out why—and learn the steps you should take to protect your horse from falling prey to this devastating condition.

How heavy is too heavy for a horse?

Considering Weight When people wonder if they’re too heavy for their horse, their main concern is weight. There is debate about this percentage, but the general rule is that a horse should carry no more than 20 percent of their weight.

How much weight can a 500 kg horse carry?

As a general guideline in the UK, a rider should weigh no more than 10% of the horse’s bodyweight, but in the US, this limit is doubled to 20% of the horse’s weight. This means for a 500kg horse, the range for the maximum rider weight is large – 50kg in the UK (just less than 8st) and 100kg in the US (15st 10lb).

How much should my horse weight?

An average horse weighs 900-2,000 pounds, depending on size and breed. A lean, racing fit Thoroughbred, for example, has an average weight of 900-1,100 pounds, while the average Clydesdale (think Budweiser) weighs in at 1,800-2,000 pounds.

How to Weigh a Horse

A weight tape may be used to estimate a horse’s weight with great accuracy. The formula approach, which requires two inches measurements to be taken, is the most exact way. It is recommended to use the formula technique when a weight scale is not accessible or is not possible. 1. Take the following measurements: heart circumference and body length. 2. Calculate the horse’s bodyweight by applying the proper weight formula, as shown in the following table. 3. To more accurately track the horse’s progress over time, measure him at the same time of day every day, ideally first thing in the morning before eating.

Measuring the Horse

Place a measuring tape over the horse’s withers, keeping the tape as near to the horse’s elbows as feasible. Measure around the horse’s girth. Inches are the unit of measurement.

Measure with two persons from the point of the shoulder, straight back down the horse’s side, to the point of the buttock or the crease as indicated in the illustration. Inches are the unit of measurement.

Equine WEIGHT Formulas(1)(Measurements in Inches)

For an adult horse, multiply (Heart Girth x Body Length) by 330 to get the horse’s weight in pounds. Yearling: (Heart Girth x Heart Girth x Body Length) 301 = Bodyweight in pounds
(Heart Girth x Body Length) 301 = Bodyweight in pounds
Weight of a weanling is calculated as follows: (Heart Girth times Heart Girth times Body Length)/280 Equals bodyweight in pounds.

Weight Management Tips

In addition to immunizations, deworming, dental care, and exercise, a horse’s overall health care regimen should include proper diet and weight control. Slow and gradual weight loss is the most effective strategy for lowering body weight and avoiding stress and digestive disturbances. As the overweight horse grows more fit, gradually increase the amount of exercise he receives. Separately feed the overweight horse from the other horses in order to better regulate and monitor feed consumption levels. Water that is both fresh and clean should be readily available at all times. Horses should be allowed to cool down fully, including rehydration, before being fed or given unrestricted access to water. Keep an eye on the horse’s development at all times. Week by week, weigh and measure the horse and record its weight for future reference and more precise tracking
Make certain that you do not exceed or go below the appropriate feeding rate range as mentioned for the specific feed and horse you are using.

(1) Carroll, C.L., and P.J. Huntington, “An Introduction to the Theory of Probability.” Equine Veterinary Journal, volume 20, number 1, pages 41-45, 1988. Wilson, K.R., P.G. Gibbs, G.D. Potter, E.M. Michael, and B.D. Scott 2003 Proceedings of the 18th Equine Nutrition and Physiology Society Symposium. Wilson, K.R., P.G. Gibbs, G.D. Potter, E.M. Michael, and B.D. Scott P.238-242.

How To Weigh Your Horse

Every horse owner should be aware of their horse’s weight in addition to the horse’s typical, resting vital signs. Knowing how much your horse weighs will not only help you to feed him properly and monitor his overall health, but it will also become extremely important when deworming your horse and dispensing certain medications, as either an under- or overdosage could result in serious health consequences if not done correctly.

How to Weigh Your Horse

In order to determine the weight of your horse, you can employ a number of various approaches. To get the most accurate reading, weigh your horse on an electronic scale. However, unless you live near an equine veterinarian facility that has an electronic scale, this is regrettably not an option for most horse owners. Weight Tapes are a type of elastic band that is used to support a person’s weight. The heart girth (barrel) of your horse may also be measured using an equine weight tape to give an estimated weight for your horse; however, keep in mind that these tapes are built for the typical horse in terms of size, form, and overall body type.

Ponies, growing horses, huge warmbloods, and draft breeds are examples of horses that do not fit within the usual category of horses.

If your horse’s weight has to be watched, it’s ideal to take measures once a month unless there is an extraordinary amount of weight growth or loss.

Consistency is essential when using a weight tape to track weight loss or gain. Make certain you use the same weight tape and to measure at least three times in the exact same location each time, taking the average of the results. The following is an example of how to utilize a weight tape:

Check to see that your horse is standing on a level, level surface. The “zero” end of the weight tape should be held in one hand and the weight tape should be slipped over the horse’s back behind his withers. Take the other end of the weight tape and place it under his barrel, where the girth would typically be, and keep it firmly (but not too tight) on his flesh. Although you don’t want a bulky winter coat to add unwanted “pounds” to the results, it also shouldn’t be too tight that the horse becomes uncomfortable. Pull the weight tape up to meet the other end of the “zero” on the other end of the tape. The quantity that your horse weighs is shown by the figure on the weight strip where the “zero” appears.

Calculations of Body Weight Another method of estimating your horse’s weight is to just conduct a little arithmetic on your computer. When you measure both the length of the body and the circumference of the heart, you are more likely to acquire an accurate weight. With a soft measuring tape, position your horse on a level, even surface and take an inch-by-inch measurement of his heart girth, as instructed previously. Measure his body length from the point of his shoulder, straight back down his side, and down to the point of his buttock, then input the results into the formula provided below.

Make certain you apply the right formula.
When you are a yearling, multiply your heart circumference by your body length/301 to get your weight in pounds.
Heart Girth x Heart Girth x Body Length / 299 = Body Weight in pounds for a pony For example, if your horse’s heart girth is 75 inches and his body length is 60 inches, his total body weight would be 1,125 pounds.
As with any measurement, there are a variety of factors that might impact its accuracy.

Learn to Calculate a Horse’s Approximate Weight

You may need to know how much your horse weighs from time to time. Being aware of your horse’s body weight is vital for providing medicines, deworming, and keeping an eye on your horse’s general health.

Livestock Scale

Equine weight may be accurately measured using a livestock scale, which is the most precise method available today. Some veterinary clinics have livestock scales, while some may have portable scales available to their clients. Scales are commonly found at auction barns. If you bring your horse to one of these locations, it is probable that you may be able to have him weighed on a scale.

Truck Scale

A truck scale may also be available to you, but you will have to load your horse into your trailer in order to transport him there, and then weigh the entire rig, both with and without the horse loaded on. Weight of the horse will be equal to the difference between the two weights. It is important to weigh your horse and your empty trailer on various days since factors such as how much equipment you have stored away and how much petrol is in the tank will have an impact on the total weight.

When compared to livestock scales, truck scales are not as precisely calibrated, and the weight may be off by as much as 20 or 40 pounds, depending on how the scales are set up. Obtaining a weight in this manner is difficult and time-consuming.

Measuring Your Horses Body

If you are unable to measure your horse using a livestock scale, you can estimate its weight by measuring the horse’s body length. A specific weight tape can be used to obtain an approximate weight measurement. Weight tapes are available in both attack shops and feed stores for purchase. They are low-cost and simple to use, making them an excellent choice. In part, this is due to the fact that these measurements are made solely around the horse’s girth and do not take into account other factors such as fat/muscle ratio, height, body type, and overall condition.

Take measurements around the horse using a weight tape that you have purchased, making sure that the tape runs around the girth region and up over the horse, just behind the withers.

Keeping track of your horse’s weight requires you to be very careful that the tape is placed in precisely the same spot each time and that the tension on the tape is the same.

Weight cassettes that are tailored to certain body types are available for purchase.

Weight Chart

You do not, however, require a particular weight tape in order to obtain an estimated weight. It is possible to use a conventional tape measure or a piece of twine that has been measured. Using the weight table available on the OMAFRA website, it is possible to establish an approximate weight. Alternatively, you may measure around the horse as indicated above and then take a second measurement from the point of the horse’s shoulder to the ‘edge’ of the hindquarters to get an estimated weight.

It is correct that you double the circumference measurement around the girth two times.

So, if your horse is 76 inches in circumference and 38 inches in length, you would figure 76 x 76 x 38 = 782 pounds by multiplying the circumference by the length.

Estimating Weight

Traditional weight estimation formulae include the girth times the body length multiplied by 300 and the Horse’s weight technique, although there are more formulas that may be used. A More Accurate “Weigh” for Horses: Estimation of the weight of horses examines the precision of commonly used formulae and proposes a somewhat alternative method of measuring and estimating the weight of an object. When it comes to ponies and foals, this calculation will not be as exact. Here is a formula for calculating the weight of a foal.

Please keep in mind that all of these approaches, with the exception of the livestock scale, will be based on approximations.

These approximations should be sufficient for determining feed, medicines, and supplementation requirements. If you want a very exact weight, however, you should contact with your veterinarian to determine the best way.

How to Weigh a Horse (Easy Step-by-Step Guide)

Horses are huge animals with a wide range of sizes based on the breed and the environment. A “typical” horse may weigh 1,000 lbs, however weights can range from as low as 200 lbs for a tiny horse to more than 2,000 lbs for a draft horse, depending on the species. In order to precisely calculate feed rations and medicines for your horse, you must first determine how much he weighs. The ability to accurately determine your horse’s weight is critical to keeping them healthy. There are three commonly used methods for weighing a horse.

The next best technique is to estimate your horse’s weight using a weight tape or an internet calculator, which is the second most accurate method.

How to Weigh a Horse Using a Scale

Using a livestock scale to weigh a horse is the most convenient and accurate technique of weighing horses. Your big animal veterinarian would undoubtedly have one at their clinic, but it is doubtful that it would be available for farm visits or consultations with your animals. Using a livestock scale to weigh your horse, calculate the weight of your horse using the weight tape formula technique (discussed below). Make a note of the difference so that you may be even more precise in the future when using a weight tape to measure your progress.

Then you would weigh your vehicle and trailer with the horse loaded, then remove the weight of your truck and trailer when they were not loaded with the horse.
Keep in mind that truck scales are often accurate to within one percent of the reading.
Also take into account any gasoline that you used throughout this procedure.
Please do not unload your horse at the grain elevator; doing so might endanger your safety or put you in legal danger.
And, please, do not attempt this during harvest!

How to Weigh a Horse Without a Scale

The majority of horse owners do not have access to a scale, and even fewer do so on a regular basis. The use of a weight tape is the second most precise method of determining your horse’s weight. The weight tape allows you to accurately measure and estimate the weight of your horse. It can be relatively accurate depending on the breed of your horse and the method used to determine it. In order to obtain more exact measurements, it is recommended that you enlist the assistance of a buddy. Some weight tapes create an estimate based only on the heart girth measurement; they are less accurate than the weight tape formula approach, which is more accurate.

The formula technique necessitates a little mathematical calculation (or the use of an internet calculator), but it is far more accurate.
If you choose to do this, wrap a measuring tape over the horse’s neck; the tape should be directly above where the girth of the saddle would be, or about 4″ behind where the elbow would be, depending on your preference.
After that, take a measurement of the horse’s length.
Depending on the situation, this line could not be horizontal and instead slant up from front to rear.

Please keep in mind that this is NOT the same as measuring for a blanket! Once you have your dimensions, multiply and divide them according to the formula for an adult horse as follows: Calculate approximate weight in pounds by dividing (heart circumference * heart circumference * length) by 330.

A yearling would be divided by 201, rather than the more common division of 330. A weanling, on the other hand, would be divided by 280 rather than the more common division of 330.

It is crucial to remember that this recipe will not work for every horse. It is most accurate for horses weighing roughly 1,000 pounds and standing approximately 16 hands high. Overall, this method is accurate for quarter horses, however it overestimates the weight of thoroughbreds while underestimating the weight of warmbloods. The results are not correct for ponies or minis. Maintaining your focus on the fact that weight tapes are still estimates, but they may be useful in tracking changes and recognizing trends once you’ve established a baseline Watch this little video to learn how to weigh a horse using a weight tape:

How to Guess a Horse’s Weight

The least accurate of the three approaches covered in this article is estimating a horse’s weight by eyeballing the animal. When employing this strategy, people tend to be 20 to 25 percent off the mark! It is preferable to use a weight tape, obtain a scale, or utilize an online horse weight calculator rather than guessing.

Frequently Asked Questions

Most individuals do not have access to a scale large enough to weigh a horse, therefore they rely on a weight tape as their primary way of weighing a horse. If you take only two measurements and do a little arithmetic, you’ll have a relatively accurate estimate in no time.

How accurate is horse weight tape?

A weight tape in conjunction with the “formula technique” (heart girth measurement * heart girth measurement * length of horse) yields results that are often within 5-10 percent of the actual body weight of the horse. The approach of just “eyeballing” your horse’s weight is substantially less reliable, with mistakes as high as 20-25 percent reported when using this method.

How do you weigh a horse for worming?

If you don’t have access to a scale, the next best thing to do is to use a weight tape and apply some simple arithmetic to determine how much your horse weighs. This will lead you to a decent estimate, which will allow you to determine how much wormer to administer to the animals.

How do you weigh a miniature horse?

Due to limitations in accuracy, the weight tape / formula technique is less accurate for ponies and completely inaccurate for tiny horses. The World Equine Veterinary Review developed a weight table for miniature horses, which is available online. This table takes the measurement of the heart girth and transforms it to an estimate of the body weight expressed in pounds. A livestock scale is the most accurate method of weighing your miniature horse.

Is there draft horse weight tape?

While there isn’t a weight tape designed expressly for draft horses, the same weight tape / formula procedure may still be used to get a pretty accurate reading on a draft horse’s weight and height. Thiswebsitesells a weight tape that is said to measure up to 20hh in thickness.

Parting Thoughts

It is critical to understand your horse’s weight since it has an impact on their general health and well-being. Invest in a weight-tapping device, set a baseline, and check in on yourself on a regular basis.

You should take measurements of your horse’s body at that weight if you have access to a scale so that you can determine weight more precisely in the future. P.S. Did you find this article interesting? Go to the following address:

The Biggest Loser: A Beginner’s Guide to Horse Weight Loss
Tips and Tricks: How to Assist Senior Horses in Putting on Weight
What is the average weight of a horse? (Fun facts, calculator, and frequently asked questions)
7 of the World’s Largest and Burliest Horse Breeds
Horse Weight Gain for Beginners Made Simple: Hard Keepers Made Simple
Reasons why (good) horseshoes do not cause injury to horses
What Horses Eat (And Why They Eat It)
What Horses Eat (And Why They Eat It)
Improve the Quality of Your Ride: There are six tall horse breeds.

Sources/References:

Heart Girth (inches):				Est. Weight:
Body Length (inches):
Age:

Weighing tapes are intended for horses of ordinary size and form, as well as for horses with a balanced body proportion, such as a 16-hh riding horse weighing 1,000 lbs. It is possible, however, that you may want a more exact technique of estimating your horse’s body weight if he is not of ordinary height and length (think ponies, draft breeds, and especially long horses). The age, length, and heart girth (barrel) of a horse are taken into consideration by our Equine Weight Calculator, rather than only the heart girth, as is the case with standard weight tapes.

The measurements required for our Equine Weight Calculator are simple to take; all you need is a soft, flexible tape measure to complete them.

SmartPak strongly advises you to speak with your veterinarian if you have any particular queries about your horse’s health or welfare.

Estimate Horse Weight

Knowing your horse’s weight, even if it’s only an estimate, may be quite beneficial. Knowing how much a horse weighs is useful for a variety of reasons, including calculating feed rations and determining how much de-wormer to provide, among other things. There are various methods for estimating a horse’s weight that are regularly utilized, even if it is not always practicable to find a scale large enough to handle a horse. Below: The weight of this horse, measured on a livestock scale, was 1,320 pounds.

A comparison of the estimated weights to the actual weights on a livestock scale was then performed.

Height / Weight Tapes

The usage of a height/weight tape is perhaps the most frequent approach that individuals use these days to determine their horse’s weight and height. To use one of these tapes, all you have to do is wrap the tape over the horse’s girth (also known as the “heartgirth”) and read the estimated weight printed on the tape. It may be of interest to know that there are numerous different manufacturers of height/weight cassettes, and that the figures they offer might range from one another. Generally speaking, the estimations are close, but determining which tape is the most accurate for your horse can be difficult unless you can also weigh your horse on a livestock scale and compare the figures can be tricky.

WeightCalculation

In addition, measuring the horse’s circumference and length with a “normal” tapemeasure (the sort that measures in inches) is another method of estimating the horse’s weight. After that, you’ll need to do the following calculation: Weight is calculated as follows: heart girth X heart girth X length, divided by 330, plus 50.

As an illustration: In this case, the horse’s heart girth would be 78″ and his length would be 65″, and the computation would be as follows:78 X 65 = 330 + 50 = 1,248 pounds, which is an approximate weight. How to get the necessary information for the weight calculation:

Measuring Heart Girth

To measure a horse’s heart girth, start at the base of the withers and work your way down to a couple of inches below the horse’s front legs, under the belly, and back up the opposite side to where you started. As illustrated by the blue line in the image below, this will cause your tape measure to run at an angle. It is this measurement that will be used to determine your horse’s heart girth.

Measuring Body Length

To determine the length of a horse, measure the distance (in inches) between the point of the shoulder and the point of the rump. Remember that this may cause your tapemeasure to run at an angle, as seen by the blue line in the image below. The length of your horse is determined on the measurement you take.

Estimated Weights Vs. Actual Weights

According to the illustrations and instructions above, the three horses shown below were measured and their estimated weights were calculated based on their measurements. Then we used a height/weight tape to see how much weight it estimated based on the height. At the end of the process, we weighed them on a livestock scale to see how closely they compared to their estimated weights. The entire process took approximately 1 1/2 hours and took place on the same day. Horse115:1-hand mare with a long neck.

Length: 68 inches Estimated weights:

1,288 pounds calculated based on body weight
1,187 pounds measured using a height/weight tape

On a cattle scale, the actual weight was 1,320 pounds. Horse215 is a hand-gelded horse. The circumference of the heart is 76.5 inches. The length is 68 inches in length. Estimated weights are as follows:

1.256 pounds calculated
1.187 pounds measured using a height/weight tape

On a cattle scale, the actual weight was 1,320 pounds. Horse315 is a hand-gelded horse. The circumference of the heart measures 78 inches. The length is 65 inches in length. Estimated weights are as follows:

1.172 pounds
1.248 pounds calculated based on height and weight tape

The Results

Calculation of Horse1’s weight is 1,320 pounds. Difference in pounds between actual weight and weight calculation estimate is 32 pounds. Tape Measure 1,320 inches in height and weight 1 187 lbs actual weight 133 lbs estimated height/weight tape 133 lbs difference Calculating the weight of a horse2 1,320 The actual weight is 1,256 lbs. Estimated weight difference of 64 pounds based on calculation Tape Measure 1,320 inches in height and weight Weight in actuality: 1,187 lbs. Estimated height/weight difference based on tape measure (133 pounds) Calculating the weight of a horse3 is 1,330 pounds.

in height and weight The actual weight is 1,172 lbs.

In Conclusion

When compared to the horses’ weights on a scale, neither the height/weight tape nor the weight computation provided an accurate approximation of the horses’ weights in our experiment. When comparing the usage of theheight/weight tape and measuring for the computation, the height/weight tape was significantly more convenient. For one person, it was quite simple to wrap the height/weight tape over the horse’s heart girth and read the approximate weight. After repeated use, we noticed that we instinctively placed the height/weight tape in the same location each time, resulting in consistent weight estimations.

It wasn’t really tough, but it was much easier to do with two people rather than one.

We found that adjusting the length measurement by one inch (either longer or shorter) resulted in an approximate variance in weight estimation of around 20 pounds in our experiment (heavier or lighter).

Although neither approach was completely exact, the height/weight tape proved to be far more reliable in terms of producing consistent results.

It is possible that “weighing” a horse with a height/weight tape over time may not provide 100 percent exact findings, but it will provide a good comparison of relativeweights for a horse, which means that you will at least know approximately how much weight the horse is gaining or losing.

Notes

Using the height/weight tape, we wrapped it around the horses’ heart girth from the base of the withers to just behind their front legs to determine their height and weight. Using a height/weight tape in this manner is, to the best of our knowledge, the right and most usual method of doing so. However, we are aware of individuals who believe that the proper method to use thetape is to place it at the top of the horse’s withers rather than at the base. Just for fun, we tried the same thing with the horses, and it boosted the horses’ projected weights by 50 to 60 pounds, which was still less than their scale weights.

We also measured this manner, and it resulted in each horse’s weight being 100 – 176 pounds more than their scale weights.
However, utilizing scales that are relatively dependable is one method of attempting to obtain the most accurate findings.
What to Do.
How to Bridle a Horse.
How To Take Care Of A Silk Wild Rag.
How to Look After Your Saddle Pad or Blanket.
A Chain Latch is used to close a gate.

Calculate the weight of a horse.

Braid the tail of your horse in a fishtail.

How Intelligent Are Horses?.

Make a Bridle Rack out of a couple of tin cans.

Using a horn, fashion a flag boot.

How to Make Your Own Horse Fly Spray.

How to Measure the Height of a Horse.

Sort Through Your Wild Rags.

Installing a Speed Burner on a Honda.

Understanding Common Horse Face Markings.

Putting A Stop To A Squeaking Saddle Take Horse Photographs.

How to tell the difference between a horse skull and a cow skull.

How to Tie a Horse.

Make a Stopper Knot at the end of the rope.

How to Make a Stopper Knot for a Honda Make a stopper knot for an honda that has been knotted.

A Bridle Path Needs Trimming.

Western Stirrups should be turned.

Weigh a horse and determine the optimal rider weight.

Rubber-wrapped Saddle Horns are available.

What Is / Are Horse Tips and How Do They Work?

Who Was This Person? Some of the photos and/or other content on this website are the property of their respective owners and are protected by copyright laws. All other content is protected by CowboyWay.com’s copyright from 1999 until 2022. All rights reserved.

How to Use a Tape to Weigh a Horse

Article in PDF format Article in PDF format Knowing how much weight your horse weighs can assist you in determining his dietary requirements as well as the right dosage for dewormers and other drugs to provide. If you don’t have access to a large scale, you may easily weigh your horse with a tape measure if you don’t have one. Use a tape measure that has been marked specifically for the purpose of weighing your horse, or just a regular tape measure.

1 Request a weight tape from your feed supplier. Instead of inches, the markings on a weight tape are in pounds. It is constructed of a nice and durable material. A horse’s weight is estimated with a weight tape by measuring the horse’s heart girth. The weight tape is most useful when you don’t require a precise weight but yet want to be accurate.

Weight tapes are available for purchase through catalogs, although many feed merchants provide them for free. Weight tapes are a simple and effective technique to advertise a dealer’s products
Weight tapes are occasionally printed on both sides. The number of “hands” will be listed on one side, and the amount of pounds will be listed on the other. This side isn’t essential for measuring a horse
A weight tape produces a less precise weight estimate than a regular tape measure, thus it’s not recommended. It is possible that it is as much as 100-200 pounds off from the horse’s true weight. If you want a more accurate measurement, such as for a powerful dewormer, you should consider using a tape measure instead.

2 Place your horse on a level piece of land. Take care to ensure that the horse’s head is free of tension and that you have your weight tape on hand

As long as the horse’s head isn’t moving, talk to him gently and wait until he begins to relax. It is critical that he relaxes his head in order to obtain a more accurate weight
You should likewise be calm. Prepare yourself by taking several deep breaths and centering yourself before beginning to measure the horse. Make an effort to accomplish this on a quiet day with little breeze. Your endeavor will be made more harder by the wind.

Advertisement
s3 Place yourself on the horse’s left side. Keep the tape end with the number zero in your hand. The weigh tape should be draped over the horse’s back, right below his withers (or the tiny hump at the base of the neck)

It is possible that the tape will become twisted, and your reading will be inaccurate. If it twists, be cautious to smooth it down with your hands. If your horse is young or easily frightened, the presence of this tape draped across his back may cause him to become agitated and uneasy. Maintain your composure and refrain from changing the tape until the horse has calmed down.

4 Grab the inside of your horse’s belly with your free hand and gently pull it in your direction. Snug but not too tight is the ideal fit for the tape. Using your hand, hold the tape beside the end of the tape (which is labeled “zero”)

If you can keep the “zero” end of the measuring tape remaining adjacent to the horse’s body while pulling the measuring tape up over it, that will be much simpler. It is much simpler to complete this procedure with the assistance of a second person, especially if your horse is quickly startled.

5 Find the point on the tape where it meets the “zero” end and read the number there. This is the weight of your horse. Repeat this step as many times as necessary to achieve the optimum results. The fact that your horse’s body expands and contracts with each breath means that your measurements will be somewhat different each time.

Make certain that your thumbs or fingers are not pressed against the measuring tape as you read the measurement. Weigh your horses on a regular basis to verify that they are receiving the finest diet and health possible.

1 Take a measurement around the horse’s heart girth. As in the previous step, drape a regular soft measuring tape around the back of your horse’s neck. Maintain the tape’s position at the “zero” end

In addition to feet and inches, the tape may be measured in centimeters as well as centimeters and feet. The marking will have an impact on the computation that you will do later in the process of establishing the weight of your horse
It is better to conduct this outside of the wind. As a result of the wind, the tape measure may flap and twist, making it more difficult to manage. It is also possible that a flying tape will scare a horse, making the measurement process more difficult for both of you.

2 Gently pull the tape from beneath the horse’s belly to secure it. The tape should be a few inches behind the horse’s front legs while it is in this position. Take a measurement where one end of the tape meets the end of the tape held in your other hand, then record the value where the “zero” end meets the other side. Note down the measurement on a piece of paper

Perhaps you’ve noticed that the tape is applied at an angle from just beyond the horse’s front legs to the base of his withers. This is intentional. In my opinion, this is how it should be. Repeat the measuring procedure to ensure that you get the most precise measurement possible. b.

3 Take a measurement of the length of your horse. You will want the assistance of a second person to hold the measuring tape. Place the second person on the horse’s right side so that they can see him. The “zero” end of the tape measure should be held by this individual at the point of the horse’s shoulder.

Keep your distance from the horse’s hindquarters, otherwise he will become frightened and bolt. Constantly monitor the second person’s attention and silence.

Holding the measuring tape in your hand, walk beside the horse. After reaching the tip of the horse’s buttock or the crease, pull the tape taut to finish the job.

Make sure the tape isn’t twisted when you pull it, otherwise the precision of your measurement may be compromised. The second person may hold your notepad and pen while you take your measures, freeing up your hands to handle the measuring tape.

5 Take note of whether your measurement is in inches (in English) or centimeters (in French) (metric). You now have the heart girth and length of your horse written down on a piece of paper. The heart girth of your horse, for example, may be 78 inches, but his length might be 65 inches. If you’ve taken your measurements in centimeters, your heart girth may be 200 cm and your length might be 165 cm. You’ll need them to figure out how much your horse weighs.

If your measurements are in cm, write the number 11,990 on your piece of paper. Your body weight will be expressed in kilos. If your measurements are in inches, make a note of the number 330 on your paper. Your body weight will be expressed in pounds

6 Multiply the measured heart girth by the product of the heart girth and the length. For example, if the heart girth is 78 inches and the length is 65 inches, multiply 78 x 65 inches. You should be able to come up with the number 395,460. Divide the result of the multiplication by the number provided above to arrive at a final result of the multiplication.

If you’re measuring in centimeters, divide your total by 11,990 to get your inch equivalent. Your horse’s weight in kilos will be determined as a consequence of this calculation. Using the following equation, get the weight of a horse with a heart girth of 200 cm and a length of 165 cm: 200 times 200 times 165 equals 6,600,000. When this number is multiplied by 11,990, the final result is 550. That is the weight of your horse
If you’re measuring in inches, divide your total by 330 to get the height of your horse. The outcome will be the weight of your horse, expressed in pounds. As an example, consider the following: 78 x 78 x 65 = 395,460. When the final number is divided by 330, the result is 1,198. That is the weight of your horse.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

The estimated weight for your horse that was discovered after measuring is a very approximate weight. The method may not be acceptable for all horses, depending on their size and breed. Horses with standard bodies are the only ones who may use it
It is not suitable for ponies, draft horses, or horses with lengthy bodies. In order to get a more accurate assessment of your horse’s body weight, for example, in order to determine the right dosage of powerful medications, you’ll need to weigh your horse on a scale.

It’s a good idea to keep track of how much weight your horse is putting on. Make a note of your weight estimations in a tiny notebook that you may keep in your stable. Before you begin to measure, make sure you have your notepad nearby to take notes. When it comes time to make the computation, you don’t want to have to go back and measure anything again because you forget what the number was

About This Article

Summary of the ArticleXWhen weighing a horse with a tape, make sure that your horse is standing on level ground and that its head is calm in order to obtain a more accurate weight. To tack up your horse, position yourself on its left side and lay the tape over its back just behind its withers, or just below the tiny hump at the base of its neck. Reach beneath your horse’s belly with your free hand and gently pull the tape in the direction you want it to go. Read and make a note of the number you see, which is an approximation of the weight of your horse.

For instructions on how to weigh your horse using a measuring tape, continue reading!

It took 134,433 readers to read this page.

Did this article help you?

Knowing the weight of your horse is vital for a variety of reasons, including feeding your horse appropriately, providing medicines or dewormer paste, and keeping track of your horse’s overall health. Unfortunately, not everyone has access to scales large enough to accommodate a horse, thus the majority of horse owners must rely on a standard weight tape to determine the size of their animal. The use of a weight tape to measure your horse can be fairly imprecise at best, but it is preferable than doing nothing at all.

Consider the following: Measure the length of your horse and the circumference of their girth using a seamstress tape and record the results in inches.

The number “301” should be used for a yearling, whereas “280” should be used for a weanling.

To obtain the proper weight, enter “299.” Watch our YouTube video on how to measure your horse without using a scale to see a demonstration: How to Measure Your Horse Without Using a Scale Using this link, you may get printable versions of our formula for figuring out how much your horse weighs without the need of a scale.

Weighing Your Horse Without a Scale

“Does this saddle pad make me seem fat?” your horse will never ask you whether the saddle pad is too big for him. However, it is beneficial to him if you keep an eye on his weight for him. Even while weight fluctuation is normally correlated with feed consumption, drastic variations in condition might indicate the presence of a dangerous sickness. undefined You can, of course, “eyeball” your horse’s condition, and, if you have access to one, you can use a livestock scale to keep an absolutely accurate track of how much weight your horse is carrying.

body weight (measured in kilograms) =/ 11,877 lbs.
Measure the length of the horse’s body starting at the center of the front of the chest and continuing straight back along the horse’s side to the center of the tail.
As an illustration: It would be necessary to divide 11,877 by 190.5 to get the length of an 80-inch-girth horse with a body length of 80 inches (203.2 inches).
It is computed that the body weight is 621 kilograms, which is equal to 1,366 pounds.

(A mature horse’s length should remain constant, though a significant weight loss or gain will have an impact on it.) In order to achieve the best results, maintain complete consistency in your measuring technique by placing the tape measure in the same location and holding it with the same tension each time you evaluate your horse.

This article first appeared in EQUUS 270 (April 2000). (April 2000).

How to Estimate Your Horse’s Weight

For many years, I believed I was “on the money” when I stated that my horse weighed 1200 pounds. It turns out that he weighs 900 pounds. My eyes are plainly not up to the task of playing this game! It’s critical to estimate your horse’s weight for a variety of reasons, including:

Dietary analysis
Supplement and wormer dosages
And other services. Monitoring of one’s health
Weight patterns for your horse on a broad scale

You can rapidly determine the weight of your horse if you have access to a livestock scale – but who has access to a livestock scale on hand? The use of a weight tape may make estimating the weight of your horse much easier.

Here’s how to estimate your horse’s weight with a weight tape:

Draw a line along these lines and take your measurements.

Take your measures in centimeters or inches, from front to back and around the centre of the garment. Unless you have a freakishly enormous wingspan because you are a giant, you should enlist the assistance of a buddy to ensure that your beginning and finishing places are precise.

The measurement from the point of the shoulder to the point of the buttocks is called the front-to-back measurement. It’s not the same as measuring for a blanket! So, don’t be concerned about the fact that this line may not be horizontal

Wrap the measuring tape around your horse’s barrel for the around the center measurement, which is also called as the heart girth measurement informally. Then, starting at the highest part of the wither, work your way snugly behind both elbows. Afterwards, move your tape about an inch or so closer to the tail.

This useful tape measurer may also be used to determine the height of your horse.

Now bust out the math.

It is about the same weight in pounds as the following: (Birth in inches x Girth x Length) / 300 = Approximate weight in pounds
(Birth in centimeters x Girth x Length) / 11,900 = Approximate weight in kilograms

You now have a starting point for your weight! Checking your horse’s weight on a regular basis is a smart practice. You may need to make changes to your horse’s nutrition, exercise program, or other aspects of his daily routine in order to keep him at an appropriate weight. Due to the fact that this is only an estimate, it is recommended that you consult with your veterinarian or equine nutritionist.

Read this award-winning post to learn about the consequences of an overweight horse. When it comes to weight tape, you can find it right here. As an Amazon Associate, I receive commissions on qualifying purchases made by my customers at no additional cost to them. Thank you very much for your assistance! Weighing tape– although these tapes come with instructions on how to measure weight, it is recommended that you utilize the procedure outlined above for more accurate results. Thank you very much!

How to work out your horses weight

How to accurately determine the weight of your horse in order to dose properly Calculating the right dose for worming horses is accomplished by taking the horse’s weight into consideration. It is critical that you make every effort to determine the exact weight since erroneous weight estimation might result in either over- or under-dosing of the medication. Underdosing has recently been identified as one of the most important factors contributing to the development of resistance to some active components used in horse wormers.

Calculating the weight of a horse Scale for weighing The most precise method of determining a horse’s weight is to use a weigh scale to weigh the horse.
While public weighbridges are accessible, their position is most likely inappropriate for loading and unloading horses due to the nature of their operation.
Weighing Tape is a type of tape that is used to measure the weight of an object.
Using a basic length measurement or by using a combination of both.
Calculating the weight of your horse with the use of a formula.
Apply a light tension to the weigh tape around the horse’s neck and take the weight at the point where the green, free end of the weigh tape ends.
As soon as the horse has breathed, take the reading while holding the tape tightly in place.
Miniature horses and foals do not respond well to tape treatments.

The following formula can be used to compute a horse’s weight as an alternative to using a weigh tape, and it may result in a slightly more accurate measurement than using a weigh tape.

Adult horses: (girth measurement in cm) x (girth measurement in cm)x (length measurement in cm)÷ 11800= weight in kgs

How to weigh your horse – KPP

Simply admire the soft and cuddly horse, who is dressed in a wonderful warm winter coat. Do you ever think to yourself, “He definitely seems obese and sassy, but is he really?” Is it possible that my horse is losing weight? “How am I supposed to tell what’s going on behind all that hair?” Using a scale is the most accurate way to keep track of your horse’s weight, but not everyone has access to a scale large enough to weigh a horse properly. For a more affordable alternative, you might use a weight tape to determine your horse’s weight.

Although the tape may not provide an accurate weight reading, if you measure your horse in the same manner each time, you will have a fair notion of whether or not they are gaining or losing weight.

1) Place your horse on a smooth, level place and ask him to stand squarely on his hind legs.

3) Pull the tape snugly, but not too tightly, around the neck.

After you’ve taken measurements of your horse’s circumference around its heart girth and his overall length from the tip of his shoulder to his buttock, you’ll need to put those figures into an appropriate calculation.

For a pony, multiply the heart girth times the heart girth times the body length by 299 to get the body weight in pounds.

You may get a free adult horse calculator on the website of the Horse magazine.

Equi-Jewel® Rice Bran is an excellent choice if you need to supplement your horse’s diet with extra calories throughout the winter months.

It is a good approach to keep your weight under control throughout the harsh winter months.